|
 
| 产品特点Features | 一、两阀座密封三通球阀结构紧凑、外型美观、密封性能好。它能实现对管道中介质流向的切换。也能使相互垂直和两个通道两桶或关闭(如流向图A)。
二、四阀座密封三通球阀造型美观，结构紧凑合理，它不仅可实现介质流向的切换，也可使三个通道相互连通，同时也可关闭任一通道，使另外两个通道连通，灵活控制管路中介质的合流或分流(如流向图B)。
1.in the double-seat sealing design,the 3-way ball valve enjoyscompact structure,goodly configuration and favorable sealingperformance.The value could make a realization the switching offlow direction of the medium inside the pipeline,furthermore,it also could connect or shut-down the two orthogonal passages(As shown in Flow Graph A).
2.ln the 4-seat sealing design,the 3-way ball value enjoys reasonable,compact structure and goodly configuration.The value could not onlymake a realization the swithing off low direction of the medium insidethe pipeline,but also connect the 3 passages on another.Meanwhile,the value also features the capacity of shutting-down one of the 3passages while connecting the other 2 0nes for the flexible controlof the convergent flow or shunting of the medium in pipelines (As shown in Flow Graph B). |
主要零件及材质Main parts and Material 零件名称 Accessory name
| 材质Material |
GB |
ASTM | | 阀体、阀盖Body、bonnet | WCB | A216-WCB | 密封圈Seat
| PTFE、对位聚苯
PTFE、Counterpoint
polyphenyl | PTFE、对位聚苯
PTFE、Counterpoint
polyphenyl | | 球体BajI | 1Cr18Ni9Ti | SS 304 | | 阀杆Stem | 2Cr13 | A276-410 | 双头螺柱
Dual-head
double-screw bolt | 35CrMoA
| A193-B7 |
备注：三通球阀一般采用两阀座结构，如流向图A所示两种工况。选用两阀座L型结构（即Q44型）。流向图B中①和④两种工况亦可选用两阀座T型结构（即Q45型）。流向图B中②和⑧两种工况必须选用四阀座T型结构（即Q45型）。其余工况也可选用四阀座结构，但应在订货合同中注明阀座结构。如阀门有其他要求请参阅样本填写相应和要求代号。 主要性能规范 Main Performance Spcification 公称压力
PN(MPa)
Norninal pressure | 试验压力(MPa)Test pressure | 壳体
Shell | 高压液密封
High-pressure
liquld sealing | 低压气密封
Low-pressure
hermetic sealing | | 1.6 | 2.4 | 1.76 | 0.6 | | 2 5 | 3.75
| 2.75 | | 40 | 6 0 | 4.4 | | CLASS150 | 3.0 | 2.2 | 应用规范
Applicabla
Specification | 适用介质
Applicable
medium | 水、油品、气等非腐蚀介质和酸碱腐蚀介质
Non-corrsion medium such as water
and gas,etc,and nitric acid
corrosion medium | 适用温度
Applicable
temperature | -28 - 280℃ | 适用工况
Applicable | 连接法兰
Connectingflanger | JB79-94、GB9113、 HG20592-09、ANSIB16.5 | Operating
Mode | 检验试验
Test and inspection | JB/T9092-99. AP1598 | 其余制造规范均按本厂标准
Other manufacturing standard is according to the standard of factory |
Remarks:
Double-seat configuration design is generally utilized for 3-way ball value as shown in the 2 0pratingconditions in Folw Graph A which apply the L-Shaped construction with double-seat(Type Q44).With regard to the 2 condition of ①and ④ in flow Graph B,the T-shaped construction with double-seat could also be applied(Type Q45).ln the ② and ③ conditions in this graph, the choice of the cinstruction must be limited to T-shapedones with 4-seat(Type Q45).For other kinds of opeqating conditions, the construction with 4-seat could also be applied,however,the construction of the relevent valve seats should be referred in advance in the contractfor future delivery.For other requirements please refer to the sample of Organizing Methord for Types of Ball Valves and fill in corresponding code numbers as required. Remarks:
Double-seat configuration design is generally utilized for 3-way ball value as shown in the 2 0pratingconditions in Folw Graph A which apply the L-Shaped construction with double-seat(Type Q44).With regard to the 2 condition of ①and ④ in flow Graph B,the T-shaped construction with double-seat could also be applied(Type Q45).ln the ② and ③ conditions in this graph, the choice of the cinstruction must be limited to T-shapedones with 4-seat(Type Q45).For other kinds of opeqating conditions, the construction with 4-seat could also be applied,however,the construction of the relevent valve seats should be referred in advance in the contractfor future delivery.For other requirements please refer to the sample of Organizing Methord for Types of Ball Valves and fill in corresponding code numbers as required. 
公称压力
或压力级
Norminal pressure | 主要尺寸 | 公称通径DN（mm/in）Nominal diameter | | 15/l/2" | 20/3/4’ | 25/1" | 32/1 1/4" | 40/1’/2" | 50/2" | 65/21／2^" | 80/3" | 100/4" | 125/5" | 150/6" | 200/8" | | PNl.6MPa | L | 150 | 150 | 180 | 200 | 220 | 240 | 260 | 280 | 320 | 380 | 440 | 550 | | PN2.5MPa | L1 | 75 | 75 | 90 | 100 | 110 | 120 | 130 | 140 | 160 | 190 | 220 | 275 | | PN4.OMpa | H | 90 | 90 | 102 | 115 | 135 | 140 | 155 | 185 | 210 | 275 | 305 | 335 | | CLASS 150 | W | 140 | 140 | 155 | 250 | 250 | 350 | 350 | 420 | 700 | 1000 | 1300 | 1800 | 其余的法兰尺寸请参阅样本《主要外形及连接尺寸表》
Please refer to the sample book of Form of Main Type and Commecting Dimension for other flange dimensions |
|
